IEC 80 · 230/400 V
Representative model from frame 80 dimensions
Tap a partDrag to rotate · scroll to zoom
0.75kWRated output · 50 Hz
1440rpmRated speed
79.6%Efficiency, full load
5NmRated torque
1.9ACurrent at 400 V
0.72Power factor
12kgWeight, B3
3.8× MNStarting torque
Performance · 50 Hz, tested values
| Output | 0.75 kW |
|---|---|
| Poles · synchronous speed | 4 · 1500 rpm |
| Rated speed | 1440 rpm |
| Rated torque MN | 5 Nm |
| Current at 230 V | 3.3 A |
| Current at 400 V | 1.9 A |
| Current at 690 V | – |
| Current at SF 1.15, 400 V | 2.1 A |
| Efficiency 100 / 75 / 50 % | 79.6 / 78.8 / 77.4 |
| Power factor 100 / 75 / 50 % | 0.72 / 0.62 / 0.49 |
| Efficiency class | IE2 (IEC 60034-30-1) |
| Locked-rotor torque MA/MN | 3.8 |
|---|---|
| Starting current IA/IN | 6.8 |
| Breakdown torque MK/MN | 3.8 |
| Pull-up torque MS/MN | 1.8 |
| Rotor inertia J | 0.0019 kgm² |
| Sound pressure LPA at 1 m | 47 dB(A) |
| Insulation | Class F, temperature rise class B |
| Enclosure · cooling | IP55 · IC411 TEFC |
| Ambient | −20 °C to +40 °C |
| Service factor | 1.15 at 400 V 50 Hz (S1) |
| Bearings DE / NDE | 6204ZZ / 6003ZZ |
Torque–speed curve indicative
Drawn through the catalogue points MA, MS, MK and MN. Request the tested curve for your application.
Part-load performance
Efficiency determined to IEC 60034-2-1. Values on a 400 V winding (230 V for single-phase), subject to IEC tolerances.
Dimensions · IM B3, frame 80
Schematic outline for orientation, not to scale for manufacture. Request the certified drawing (PDF / DXF / STEP) with your enquiry.
| AFoot hole spacing, end | 125 mm |
|---|---|
| BFoot hole spacing, side | 100 mm |
| CShaft shoulder to foot hole | 50 mm |
| HShaft centre height | 80 mm |
| KFoot hole diameter | 10 mm |
| LOverall length | 278 mm |
| ACBody diameter | 160 mm |
| HDOverall height | 212 mm |
| DShaft diameter | 19 mm |
| EShaft length | 40 mm |
| MFlange B5 · pitch circle | 165 mm |
| NFlange B5 · spigot | 130 mm |
| PFlange B5 · outside diameter | 200 mm |
| SFlange B5 · hole diameter | 12 mm |
Mountings B3, B5, B14, B35 and B34 on every rating. Shaft tolerance to IEC 60072. NEMA frames 56C to 256T built to MG 1 on request.
Documents & next steps
PDF
RFQ
DWG
Datasheet
EMPD-DS-IE-01 · Rev 2.1
Request a quote
Model EM2-80-4-0.75 filled in for you
Certified drawing
PDF, DXF or STEP on request
Related motors
EM2-80-2-0.75IE2 · 3-phase · 0.75 kW · 2P · 2880 rpmEM2-80-4-0.55IE2 · 3-phase · 0.55 kW · 4P · 1410 rpmEM2-90S-4-1.1IE2 · 3-phase · 1.1 kW · 4P · 1425 rpmEM2-90S-6-0.75IE2 · 3-phase · 0.75 kW · 6P · 935 rpmEM2-100L-8-0.75IE2 · 3-phase · 0.75 kW · 8P · 690 rpmEBM-D80-4-0.75Brake motor · 0.75 kW · 4P · 1440 rpmEBM-A80-4-0.75Brake motor · 0.75 kW · 4P · 1440 rpmEM1C-90L-4-0.75Single-phase · 0.75 kW · 4P · 1420 rpm