IEC 160L · 400/690 V
Representative model from frame 160L dimensions
Tap a partDrag to rotate · scroll to zoom
15kWRated output · 50 Hz
1460rpmRated speed
90.6%Efficiency, full load
98.1NmRated torque
28ACurrent at 400 V
0.85Power factor
92kgWeight, B3
2.5× MNStarting torque
Performance · 50 Hz, tested values
| Output | 15 kW |
|---|---|
| Poles · synchronous speed | 4 · 1500 rpm |
| Rated speed | 1460 rpm |
| Rated torque MN | 98.1 Nm |
| Current at 230 V | – |
| Current at 400 V | 28 A |
| Current at 690 V | 16.2 A |
| Current at SF 1.15, 400 V | 31.1 A |
| Efficiency 100 / 75 / 50 % | 90.6 / 91.8 / 91.6 |
| Power factor 100 / 75 / 50 % | 0.85 / 0.81 / 0.71 |
| Efficiency class | IE2 (IEC 60034-30-1) |
| Locked-rotor torque MA/MN | 2.5 |
|---|---|
| Starting current IA/IN | 7.7 |
| Breakdown torque MK/MN | 2.9 |
| Pull-up torque MS/MN | 2 |
| Rotor inertia J | 0.084 kgm² |
| Sound pressure LPA at 1 m | 63 dB(A) |
| Insulation | Class F, temperature rise class B |
| Enclosure · cooling | IP55 · IC411 TEFC |
| Ambient | −20 °C to +40 °C |
| Service factor | 1.15 at 400 V 50 Hz (S1) |
| Bearings DE / NDE | 6309ZZ / 6307ZZ |
Torque–speed curve indicative
Drawn through the catalogue points MA, MS, MK and MN. Request the tested curve for your application.
Part-load performance
Efficiency determined to IEC 60034-2-1. Values on a 400 V winding (230 V for single-phase), subject to IEC tolerances.
Dimensions · IM B3, frame 160L
Schematic outline for orientation, not to scale for manufacture. Request the certified drawing (PDF / DXF / STEP) with your enquiry.
| AFoot hole spacing, end | 254 mm |
|---|---|
| BFoot hole spacing, side | 254 mm |
| CShaft shoulder to foot hole | 108 mm |
| HShaft centre height | 160 mm |
| KFoot hole diameter | 15 mm |
| LOverall length | 605 mm |
| ACBody diameter | 314 mm |
| HDOverall height | 400 mm |
| DShaft diameter | 42 mm |
| EShaft length | 110 mm |
| MFlange B5 · pitch circle | 300 mm |
| NFlange B5 · spigot | 250 mm |
| PFlange B5 · outside diameter | 350 mm |
| SFlange B5 · hole diameter | 18.5 mm |
Mountings B3, B5, B14, B35 and B34 on every rating. Shaft tolerance to IEC 60072. NEMA frames 56C to 256T built to MG 1 on request.
Documents & next steps
PDF
RFQ
DWG
Datasheet
EMPD-DS-IE-01 · Rev 2.1
Request a quote
Model EM2-160L-4-15 filled in for you
Certified drawing
PDF, DXF or STEP on request
Related motors
EM2-160M-2-15IE2 · 3-phase · 15 kW · 2P · 2940 rpmEM2-160M-4-11IE2 · 3-phase · 11 kW · 4P · 1465 rpmEM2-180M-4-18.5IE2 · 3-phase · 18.5 kW · 4P · 1470 rpmEM2-180L-4-22IE2 · 3-phase · 22 kW · 4P · 1470 rpmEM2-180L-6-15IE2 · 3-phase · 15 kW · 6P · 980 rpmEM3-160L-4-15IE3 · 3-phase · 15 kW · 4P · 1475 rpmEBM-D160L-4-15Brake motor · 15 kW · 4P · 1460 rpm