IEC 132MX · 400/690 V
Representative model from frame 132MX dimensions
Tap a partDrag to rotate · scroll to zoom
5.5kWRated output · 50 Hz
950rpmRated speed
86%Efficiency, full load
55.3NmRated torque
12.6ACurrent at 400 V
0.75Power factor
60.5kgWeight, B3
2× MNStarting torque
Performance · 50 Hz, tested values
| Output | 5.5 kW |
|---|---|
| Poles · synchronous speed | 6 · 1000 rpm |
| Rated speed | 950 rpm |
| Rated torque MN | 55.3 Nm |
| Current at 230 V | – |
| Current at 400 V | 12.6 A |
| Current at 690 V | 7.4 A |
| Current at SF 1.15, 400 V | 13.7 A |
| Efficiency 100 / 75 / 50 % | 86 / 85.2 / 83.5 |
| Power factor 100 / 75 / 50 % | 0.75 / 0.68 / 0.55 |
| Efficiency class | IE2 (IEC 60034-30-1) |
| Locked-rotor torque MA/MN | 2 |
|---|---|
| Starting current IA/IN | 5.2 |
| Breakdown torque MK/MN | 2 |
| Pull-up torque MS/MN | 1.6 |
| Rotor inertia J | 0.032 kgm² |
| Sound pressure LPA at 1 m | 58 dB(A) |
| Insulation | Class F, temperature rise class B |
| Enclosure · cooling | IP55 · IC411 TEFC |
| Ambient | −20 °C to +40 °C |
| Service factor | 1.15 at 400 V 50 Hz (S1) |
| Bearings DE / NDE | 6208ZZ / 6305ZZ |
Torque–speed curve indicative
Drawn through the catalogue points MA, MS, MK and MN. Request the tested curve for your application.
Part-load performance
Efficiency determined to IEC 60034-2-1. Values on a 400 V winding (230 V for single-phase), subject to IEC tolerances.
Dimensions · IM B3, frame 132MX
Schematic outline for orientation, not to scale for manufacture. Request the certified drawing (PDF / DXF / STEP) with your enquiry.
| AFoot hole spacing, end | 216 mm |
|---|---|
| BFoot hole spacing, side | 178 mm |
| CShaft shoulder to foot hole | 89 mm |
| HShaft centre height | 132 mm |
| KFoot hole diameter | 12 mm |
| LOverall length | 489 mm |
| ACBody diameter | 255 mm |
| HDOverall height | 323 mm |
| DShaft diameter | 38 mm |
| EShaft length | 80 mm |
| MFlange B5 · pitch circle | 265 mm |
| NFlange B5 · spigot | 230 mm |
| PFlange B5 · outside diameter | 300 mm |
| SFlange B5 · hole diameter | 14.5 mm |
Mountings B3, B5, B14, B35 and B34 on every rating. Shaft tolerance to IEC 60072. NEMA frames 56C to 256T built to MG 1 on request.
Documents & next steps
PDF
RFQ
DWG
Datasheet
EMPD-DS-IE-01 · Rev 2.1
Request a quote
Model EM2-132M-6-5.5 filled in for you
Certified drawing
PDF, DXF or STEP on request
Related motors
EM2-132S-2-5.5IE2 · 3-phase · 5.5 kW · 2P · 2910 rpmEM2-132S-4-5.5IE2 · 3-phase · 5.5 kW · 4P · 1455 rpmEM2-132M-6-4IE2 · 3-phase · 4 kW · 6P · 960 rpmEM2-160M-6-7.5IE2 · 3-phase · 7.5 kW · 6P · 975 rpmEM2-160M-8-5.5IE2 · 3-phase · 5.5 kW · 8P · 725 rpmEM3-132M-6-5.5IE3 · 3-phase · 5.5 kW · 6P · 950 rpmEBM-D132M-6-5.5Brake motor · 5.5 kW · 6P · 950 rpmEBM-A132M-6-5.5Brake motor · 5.5 kW · 6P · 950 rpm